Available formats: plates, plates, plates, bars, tubes and profiles.
One of the main materials that we sell at Broncesval is Aluminum, we do it in various forms such as aluminum sheets, aluminum plates, aluminum plates, round aluminum profiles, square aluminum profiles, rectangular aluminum profiles, aluminum tube profiles and aluminum wire. Aluminum is a common metal used for both industrial and non-industrial applications. In most cases, it can be difficult to choose the correct grade of aluminum for your intended application. If your project doesn't have physical or structural demands, and aesthetics aren't important, then almost any grade of aluminum will do the job.
In Broncesval we have highly qualified personnel who can advise you on the type of Aluminum you need for your project. We work with aluminum alloys of all kinds from those who own a 99% to those used for armament, aircraft manufacturing, milling, etc.
The EN AW-1050 Aluminum Alloy Commercial purity with excellent corrosion resistance and good electrical and thermal conductivity. It is applied in costume jewelry, chemical industry, hydrogen peroxide containers, architecture, containers for pharmaceutical and food products, locksmithing, metalwork, covers, partitions, etc. Widely used for packaging applications and in products where high mechanical characteristics such as reflectors, screens, are not required?
This aluminum alloy EN AW-2024 along with 2014, 2017A and 2030 it belongs to the group of "Duraluminios". These are alloys with high mechanical resistance (comparable to that of carbon steels) and which are obtained by solutions, hardening and maturation treatments. Its main application is in the aeronautical and military industry, screws, bolts, rivets to be applied in the hardened state, before maturation.
This aluminum alloy EN AW-3003 It has a very good extrusion capacity and, depending on the heat treatment, it is very suitable for cold forming. Machinability is acceptable. The alloy can be welded well or very well by various methods. It is mainly used in the construction, chemical and food industries, home automation, household appliances, and kitchen and home packaging.
The magnesium content of this aluminum alloy EN AW-5005 , elevates its mechanical characteristics and makes it suitable for subsisting other alloys. It has medium mechanical characteristics, very good weldability, excellent resistance to corrosion and a good response to chemical or electrochemical polishing. As it contains magnesium it can be laser cut without any problem both anodizing and anodizing.
He Aluminum with Magnesium Alloy EN AW 5086 It is an alloy with high mechanical characteristics, with very good resistance to corrosion. Aluminum alloy Magnesium EN AW 5086, is applied in signaling gantries, land transport, mines, tanks, coal dryers, mine boxes, aeronautics, in naval applications such as superstructures, rudders, castles, compressed air bottles. It is used in shipbuilding structures and equipment (welded components), masts, chemical platforms, and storage tanks such as cryogenics, soldier tank trailers, and soldier rear bins.
Profiles extruded in aluminum alloy EN AW 6005 / EN AW 6005A They are characterized by medium mechanical resistance, even in welded joints, and good resistance to corrosion. They are suitable for use in general manufacturing, in the engineering and construction sectors. Typical fields of application are ladders, train and truck construction, marine construction, exterior applications, etc.
The aluminum alloy EN AW 6060 It is widely used in European countries and is the most widely used due to its high capacity for hot deformation, its high extrusion speed and its great propensity to achieve an excellent degree of aesthetic finish, in particular by anodizing. It has average mechanical characteristics and its propensity to deformation makes it ideal even for profiling of complex shapes for multiple uses with low mechanical load.
He Aluminum Alloy Magnesium Silicon EN AW 6063 Due to its great ease of extrusion, obtaining adequate mechanical characteristics, correct surface appearance and good coloring when anodizing, it has multiple applications. It has lower mechanical characteristics than 6005 and 6082 alloys, but its greater extrusion capacity allows for more complex sections. Being used for countless applications, it is the main alloy for carpentry and architectural products, as well as for standard profiles.
He Aluminum Alloy Zinc EN AW 7021 It is especially recommended for the following applications: Resin transfer molding, Compression molding, Resin injection molding, Blow molding, Thermoforming. The main alloy addition is zinc and is formulated for primary formation in forged products, not recommended for complex shapes and sharp corners. For these applications, we recommend the use of laminated products whenever possible.
He Aluminum Alloy Zinc EN AW 7075 it is the alloy with the highest characteristics in aluminum. The development of this alloy has made it possible to use it in fields hitherto reserved for steels. Aluminum 7075 zinc alloy, is applied in armament, automotive industry, hardware, ski poles, fishing rods, arrows, blow molds, stamped parts for mountaineering, etc.
ALUMINUM SHEETS 5083 RECTIFIED
Homogenized and released from O3 stresses. Precision ground, roughness Ra 0.4? M, protected with plastic on both sides. The Aluminum Alloy Magnesium in Plate 5083 rectified It is an alloy used for light machinery in general, parts that require a high degree of mechanization, side and rear walls of all kinds, base plates or work tables of all kinds, coordinate tables and transfer tables, components that need low tensions and high resistance, gauges of all kinds, displays for monitors.
ALUMINUM SHEETS CAST 5083 FD
Homogenized and released from O3 stresses. Surface cut by the 6 faces. The Aluminum Alloy Magnesium in Plate Cast 5083 FD it is used for light machinery in general, parts that require a high degree of mechanization, side and rear walls of all kinds, base plates or work tables of all kinds, coordinate tables and transfer tables, components that require low voltages and high resistance, gauges of all kinds, displays for monitors.
The aluminum alloy EN AW-2017A It is among the high strength hardenable alloys. Consequently, a heat treatment such as annealing the solution and subsequent natural aging is necessary for this alloy to develop its full potential. This can increase strength for various crowds. Due to its high strength and good workability, this alloy is used in the aerospace industry and in defense and aviation technology.
He aluminum with copper alloy EN AW 2030Despite their mechanical characteristics, screws, studs, washers, flanges, sleeves and parts are manufactured that require high mechanical characteristics with responsibility such as hydraulic cylinders and pistons. It has excellent machining behavior, with high cutting speeds and good chip removal, so its field of use is very varied.
The EN AW 3105 Aluminum Alloy It is an alloy with manganese that varies between 0.5% and 1.5%, which significantly improves the mechanical characteristics while maintaining good plastic deformability. It presents intermediate values from both a mechanical and a plastic point of view. Applications: automotive industry, air conditioning and ventilation systems, residential coatings, carpentry and panels, heat exchangers, kitchen utensils, packaging, roofing, pipes, drawing work.
He Aluminum Alloy Magnesium EN AW 5083 It is an alloy with high characteristics and resistance to corrosion in industrial environment and seawater. It is used in the construction of ship superstructures, rail cars, low temperature pressure vessels, defense applications, high strength structural towers after welding, mobile cranes, bodywork, dump trucks, platforms, hulls of pleasure boats, wagons for mines, missile components, etc.
The magnesium aluminum alloy EN AW 5754 It is an alloy of high mechanical resistance, with good resistance to corrosion, comparable to that of pure aluminum in general and even better than that of this, if it is a marine environment. It is applied in cauldron, either welded or riveted. Indicated for the manufacture of pressure vessels: for the production and storage of liquefied gases (O2, N2, A, He). Due to its great resistance to corrosion in the marine environment, it is very suitable for shipbuilding, refrigerators, ship superstructures, lifeboats, floats.
The aluminum alloy magnesium silicon EN AW 6026 It replaces other alloys of the Aluminum-Silicon family whose applications are found in the textile industry, coils, machine parts, chemistry, flanges, bolts, screws, nuts, etc. and in the automotive, electrical and electronic sector, forging, screws, bolts, nuts, threaded parts. It is an alloy that has good machinability, high strength, anodizing and hard coating, is MIG / WIG weldable, has good corrosion resistance and is friendly to the environment.
The Aluminum Alloy Magnesium Silicon EN AW 6061 It is an alloy developed to cover in mechanical characteristics the field between 6063 and the alloys of the Aluminum - Copper and Aluminum - Zinc families. The time between hardening and artificial maturation must not exceed 2 hours. This heat treatment hardening alloy has good weldability but loses almost 30% of the breaking load in the welded area. It has industrial applications such as the manufacture of molds, dies, machinery, tools, etc.
He Aluminum Alloy Magnesium Silicon EN AW 6082 It is ideal for molds in the footwear industry, plastic blown bottles, thermoforming, the rubber industry, molds and dies for the general industry. Models for casting and plates. Of general use for the construction of industrial machinery, weapons and armor. In automotive for industrial vehicles. It is used to make templates.
He Aluminum Alloy Zinc EN AW 7022 It is an alloy that was created to meet mold maker demand for a material that could offer the toughness and workability necessary for mold and equipment construction. Typical applications include thermoplastic blow molds and injection molding.
RECTIFIED Mic 6 PLATE
Stability is the defining feature of the MIC6® precision machined cast aluminum plate. Only MIC6 it is molded to near net thickness with a stress relieved granular structure to virtually eliminate wear distortion and end-use temperature fluctuations.
ALUMINUM SHEETS 7021 RECTIFIED
Heat treated, tempered and artificially matured T79. Milled surface precision, roughness Ra 0.4 µm, protected with plastic on both sides. The Aluminum sheet Zinc Alloy 7021 rectified It is especially recommended for the following applications: Resin transfer molding, Compression molding, Resin injection molding, Blow molding, Thermoforming. The main alloy addition is zinc and is formulated for primary formation in forged products. Not recommended for complex shapes and sharp corners. For these applications, we recommend the use of laminated products whenever possible.
ALUMINUM SHEETS CAST 7021 FD
Heat treated, tempered and artificially matured. Surface cut by the 6 faces. The Aluminum sheet Zinc Alloy 7021 rectified It is especially recommended for the following applications: Resin transfer molding, Compression molding, Resin injection molding, Blow molding, Thermoforming. The main alloy addition is zinc and is formulated for primary formation in forged products. Not recommended for complex shapes and sharp corners. For these applications, we recommend the use of laminated products whenever possible.